Results 1 to 6 of 6

Thread: Leaking transfer box rear seal driving me nuts

  1. #1

    Default Leaking transfer box rear seal driving me nuts

    Wondering if anyone can help.

    Try as a I might I cannot stop my rear transfer box seal leaking, a considerable amount. Iíve attached a photo of the leak after a 45minute drive in the landy this morning (after refitting a new seal for the second time.
    It is leaking out from the groove in the transfer case, where it meets the handbrake plate.

    IMG_0014.JPG

    Iíve now changed the seal twice in the past couple of weeks and it is still leaking. Last week I bit the bullet and bought a supposedly new old stock flange off ebay for lots of cash. It was covered in old Ďwaxí type material so looked authentic but I was a bit surprised to see some old scuff / dents marks on the edge of the flange when cleaned. Anyhow, the flange sealing surface looked marginally better that mine so I decided to fitted it and it has made no difference. Very frustrating.

    My next option is to fit one of the SKF / speedi-sleeves and see if that improves the seal although I suspect it will make no difference.

    Any thoughts on what I could be doing wrong / how I can fix it.

    Do you think I might be overfilling the box? Iíve been using the fill plug in the transfer box and filling until the oil comes out of the hole. Is this the right way of filling the box
    Iím assuming I using the right oil - standard EP90.
    There is clear ridge that can be seen on the photo of the flange. Could this be the issue or is there were the metail oil catch thing sits (that I had to tap on with a hammer).
    IMG_0014.JPG

    Grateful for any thoughts before I spend more money trying to fix it. If it was a little drip (as is the case for the rest of the landy) I wouldnít mind but itís not and its annoying!!


    Many thanks

  2. #2
    Consultant Richie_asg1's Avatar
    Join Date
    24th Apr 2006
    Location
    Aberdeen Scotland
    Posts
    9,411
    Reviews
    Read 0 Reviews

    Default Re: Leaking transfer box rear seal driving me nuts

    Hi,
    I don't think your problem is the seal at all. It will be play in the rear output bearing that allows the shaft to wobble in the seal. It could even be the outer case that holds the seal that is cracked, or the shims that hold the end cover on may be bent or have grit between them.
    You will need to chock wheels (as you have no handbrake), take off rear prop, handbrake drum and backplate, and remove the speedo drive from the transfer box. This assembly uses large profiled shims to adjust the end pressure on the output bearing. Check the bearing for wear grooves, replace if it is worn and clean the shims. Use thick silicone grease on the shims when you assemble them to prevent mineral oil seeping out of them.
    With no play in that bearing the seal can do it's job properly.

  3. #3
    Engineer phoenixdave's Avatar
    Join Date
    5th Oct 2009
    Location
    Isle of Man
    Age
    51
    Posts
    3,645
    Reviews
    Read 0 Reviews

    Default Re: Leaking transfer box rear seal driving me nuts

    +1 wot he said! But why would you need to tap the oil catcher thing on with a hammer, it should just slip into place easily? Where was it tight? David
    1982 ex-mil 109 2 1/4 petrol on lpg series III, 'Phoenix'

    1983 2 1/4 diesel 88" series III, 'Willy', currently in bits.

  4. #4
    Consultant Richie_asg1's Avatar
    Join Date
    24th Apr 2006
    Location
    Aberdeen Scotland
    Posts
    9,411
    Reviews
    Read 0 Reviews

    Default Re: Leaking transfer box rear seal driving me nuts

    Also make sure the transfer box base cover plate is flat, and that it is not leaking from there and just tracking back. It can sometimes take several attempts or even a new plate to get it to seal properly and most leaks that are not the seal come from there. Sometimes the nuts are put on to tight and it distorts. I think Rocky Mountain do a nice thick alloy one with fins.

  5. #5
    Engineer holly76's Avatar
    Join Date
    20th Apr 2011
    Location
    Bradford
    Posts
    4,748
    Reviews
    Read 0 Reviews

    Default Re: Leaking transfer box rear seal driving me nuts

    other things to check. how is the prop? if things are loose, or tight it can run out of balance or put loads on the shaft. check both uj's and the sliding joint - form the guy who had the front of the diff snap off, learning the hard way.

    also the correct fill is so it runs out of the level plug on the rear of the box. it's possible or oil to migrate from the main box or overdrive. so check after a run when he oil has cooled.

    from memory the actual oil level is only just up to the bottom lip of the seal, it is possible to change it without draining oil, by jacking up the rear. so if it's leaking when stood, best to look elsewhere. maybe remove the hand brake give a good clean to pin point the spot.

    the box breaths through the cover plate on top of the main box, under the seat box lip. check this Is clear.

  6. #6

    Default Re: Leaking transfer box rear seal driving me nuts

    It shouldn't leak even if the transfer box is grossly overfilled. The original 80in (which used the same seal and an interchangeable flange) was filled much higher - until they found problems with the oil migrating to the main box! Cure - drop the level.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. transfer box rear oil seal
    By madwelder1971 in forum Land Rover Defender
    Replies: 1
    Last Post: 1st Nov 2009, 12:37
  2. Diff oil leaking into rear drum - what seal do I need?
    By Lugy in forum Series Land Rovers
    Replies: 5
    Last Post: 8th Jun 2009, 21:47
  3. leaking rear main seal (again)
    By sparky00 in forum Land Rover Discovery
    Replies: 2
    Last Post: 21st Nov 2008, 13:05
  4. Rear diff oil seal leaking.
    By nickscott in forum Land Rover Discovery
    Replies: 1
    Last Post: 2nd Apr 2006, 23:36

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •